Akai RE32 Manual del operador Pagina 186
- Pagina / 192
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
176 Version 1.00
RS422
VTR LOCATE OFFSET Most VTRs require a certain amount of ‘run up’ time when synced to
external equipment. This field sets that time. When a value is set
here, locating to any position will automatically cause the system to
locate to a point slightly earlier than actually specified. In the above
example, if you locate to 1 minute, the Akai machine will actually
locate to 55 seconds.
NOTE: YOU MUST SELECT ONE OF THE SMPTE/EBU+RS422 OPTIONS AT A FRAME
RATE APPLICABLE TO YOUR AREA WHEN USING RS422 MASTER.
These options are available at all frame rates. SMPTE/EBU from the VTR is still connected
as usual and the ON-LINE key must be switched on. The Akai machine will receive timecode
information in playback from the LTC connection but, when working in slow motion, it re-
ceives timecode over RS422 making locking of the two machines tighter.
LAYBACK FUNCTION IN RS422 MASTER
LAYBACK is a process where you have material on the Akai system that you wish to ‘master’
onto a VTR or other such RS422 equipped machine (such as an RS422 DAT machine). For
example, you may receive a video tape with just dialogue on it. This is sync-transferred to an
Akai machine where it may be edited and tidied up if necessary and sound effects, music and
other ‘sweeteners’ can be added using the Akai system’s multi-track capabilities. Finally, the
whole thing is transferred back to the VTR.
To use the LAYBACK function, press LAYBACK (F1/F2). You will see this screen:
The parameters are:
LAYBACK TO TRACKS Here you may select which of the VTR’s tracks the material will be
recorded to. You may select VTR tracks 1, 2, 3, 4, 5, 6, 7, 8 (mono) or
1+2, 3+4, 5+6, 7+8 (stereo) or 1-4, 5-8 or 1-8.
TRACKS ENABLED Here you may select whether the layback (i.e. the mixdown) will be
to the VTR’s analogue tracks or its digital tracks. You may also select
ANALOG+DIGITAL which will cause the layback to be recorded to
both the analogue and the digital audio tracks of the VTR.
The soft key functions when LAYBACK key is pressed are:
PREROLL Pressing this key will cause the VTR to locate to the IN time minus
the amount set in the VTR LOCATE OFFSET field (if this parameter
is set to zero, then the default value of 5 seconds is used).
PREVIEW This allows you to ‘rehearse’ the layback (i.e. it will go into E-E mode
at the IN point and will then stop at the OUT point). This function
allows you to check whether the edit will be successful or not.
LAYBACK Pressing this will initiate the layback process (i.e. the VTR will play to
the IN point and will drop into record on the VTR. When the OUT
point is reached, it will stop).
NOTE: If tracks are accidentally enabled for record on the Akai system, they will be ignored
when using the LAYBACK function.
- Operator’s Manual 1
- Important Notice 2
- IMPORTANT 4
- Page vii 8
- Page viii 9
- FEATURES 11
- INTRODUCTION 11
- POWERING UP THE RE32 SYSTEM 19
- PANEL LAYOUT 20
- VGA DISPLAY 22
- NAVIGATING THE RE32 25
- CURSOR KEYS 25
- TRACK ZOOM KEYS 26
- SCROLL VIEW KEYS 26
- NUMERIC KEYPAD 27
- EDITING NUMERIC FIELDS 27
- ENTERING TIMECODE VALUES 27
- DATA ENTRY/NUDGE KEYS 28
- USING THE SOFT KEYS 28
- Version 1.00 19 29
- GETTING AROUND A PROJECT 31
- TRANSPORT KEYS 31
- LOCATE FUNCTION 31
- NEXT/PREVIOUS CUE 31
- JOG WHEEL 32
- JOG/SPOOL SET 32
- EDIT REGION 34
- SELECT CUE 34
- GETTING STARTED 35
- BASIC SYSTEM SETTINGS 36
- FORMATTING DISKS 38
- VGA SETUP 41
- RECORDING 45
- BASIC RECORDING 45
- UNDOING A RECORDING 46
- ADVANCED RECORDING 47
- RECORD DISKS 50
- RECORD TYPE 51
- PUNCH-IN PUNCH-OUT 55
- PLAY PLAYMUTED 55
- ORIGINAL RECORDING 55
- NEW RECORDING 55
- INPUT ROUTING 57
- INPUT ROUTING - DR16 58
- INPUT ROUTING - DD1500 60
- PLAYBACK 63
- PLAYING BACK AUDIO MATERIAL 63
- PLAY FROM 64
- PLAY IN>OUT 64
- MUTING TRACKS 65
- SOLOING A TRACK 65
- Version 1.00 57 67
- Clear entire locator? 68
- AUTOLOCATOR 69
- Version 1.00 61 71
- SELECT Q KEY 72
- Version 1.00 63 73
- MULTI-MACHINE EDITING 74
- MULTI- MACHINE EDIT 74
- COPYING A REGION 74
- MULTITRACK PASTE 76
- MULTITRACK INSERT 76
- MULTITRACK OVERLAY 77
- BEFORE SPLIT 79
- AFTER SPLIT 79
- CUE 1 CUE 2 79
- SINGLE MACHINE EDIT 80
- EDIT CLIPBOARD 80
- COPY TO CLIPBOARD 82
- CUT TO CLIPBOARD 84
- ERASE TO CLIPBOARD 86
- PASTE FROM CLIPBOARD 88
- INSERT FROM CLIPBOARD 90
- OVERLAY FROM CLIPBOARD 92
- MOVE REGION 93
- NUDGING IN/SYNC/OUT TIMES 94
- NUDGING AUDIO 94
- UNDOING A NUDGE 95
- NUDGE SET (SHIFT+NUDGE) 95
- SPLIT CUE 96
- IN->NOW (SHIFT+IN) 97
- SINGLE-MACHINE EDITING 100
- EDIT PLAY KEYS 100
- SELECT CUE/EDIT CUE 101
- EDIT TOOLS 105
- CROSSFADE TOOLS 105
- DISK MANAGEMENT 108
- SAVING PROJECTS 108
- The options available are: 114
- DISK UTILITIES 115
- DISK INFO 115
- DISK DIRECTORY 116
- COPYING FILES/DISKS 117
- DELETE FILES 121
- RENAMING FILES 122
- BACKING UP YOUR WORK 123
- FORMATTING A TAPE FOR BACKUP 124
- BACKING UP SELECTED FILES 126
- BACKING UP AN ENTIRE DISK 127
- PERFORMING THE BACKUP 128
- VERIFYING A BACKUP 130
- RESTORING A BACKUP 131
- PERFORMING A RESTORE 132
- RESTORING THE ENTIRE BACKUP 135
- NOTES ABOUT BACKUP/RESTORE 136
- ARCHIVING DATA TO DAT 139
- CLEANUP DISK 143
- MINIMISE DISK 144
- DISK COMPATIBILITY 146
- PROTOOLS IMPORT 147
- SYSTEM SETUP 151
- SETUP - MULTI 152
- RECORD SETUP 155
- CREATING A MIDI TEMPO MAP 160
- DELETING TEMPO MAP STEPS 161
- LOCATING TO STEPS 161
- SYNC SETTINGS 168
- USER KEYS 178
- RC15 CONNECTION 180
- SYNCHRONISATION 181
- SYNCING TO EXTERNAL TIMECODE 181
- SETTING TIMECODE OFFSETS 182
- VTR locate offset : 185
- 176 Version 1.00 186
- Version 1.00 177 187
- 178 Version 1.00 188
- SPECIFICATIONS 189
- 180 Version 1.00 190
- 182 Version 1.00 192
Relacionado con productos y manuales para Controles remotos Akai RE32
Controles remotos Akai RE32 Manual de usuario
(10 paginas)
(10 paginas)
Panasonic CQ-VW100U manuály
Uživatelské manuály a uživatelské příručky pro DVD přehrávače Panasonic CQ-VW100U.
Poskytujeme manuály pdf Panasonic CQ-VW100U ke stažení zdarma podle typů dokumentů:
Comentarios a estos manuales